Here you will find presentations given at COMSOL Conferences around the globe. The presentations explore the innovative research and products designed by your peers using COMSOL Multiphysics. Research topics span a wide array of industries and application areas, including the electrical, mechanical, fluid, and chemical disciplines. Use the Quick Search to find presentations pertaining to your application area.
COMSOL-News-Magazine-2017
COMSOL-News-Magazine-2017-Special-edition-acoustics
COMSOL-News-Magazine-2016

Modeling of a Helical Coil Heat Exchanger for Sodium Alanate Based on-board Hydrogen Storage System

S. Kumar[1], and M. Raju[2]
[1]General Motors R&D Center, Warren, MI, USA
[2]Optimal CAE Inc., Detroit, MI, USA

Hydrogen refueling in a metal hydride based automotive hydrogen storage system is an exothermic reaction and hence an efficient heat exchanger is required to remove the heat for fast refueling. In this paper a helical coil heat exchanger embedded in a sodium alanate bed is modeled using COMSOL. Sodium alanate is present in the shell and the coolant flows through the helical tube. A three ...

Analysis of Acoustic Response of Rooms

J.S. Crompton[1], L.T. Gritter[1], S. Yushanov[1], K.C. Koppenhoefer[1], and D. Magyari[2]
[1]AltaSim Technologies, LLC, Columbus, OH, USA
[2]Golden Acoustics, Detroit, MI, USA

The preferred acoustic response of recording studios, auditoriums and conference halls is to have an even energy response over the entire room and throughout full audio spectrum. This can be accomplished by using acoustic panels with complex surface structures that scatter acoustic waves and diffuse sound level variability over the room volume or through the use of sound absorbing materials to ...

Failure Stress Analysis of Fiber Reinforced of Composite Laminates under Uniaxial/Biaxial Loading

Z. Hasan[1], F. Darwish[2], and S. Al-Absi[2]
[1]Texas A&M University, College Station, TX, USA
[2]Jordan University of Science and Technology, Irbid, Jordan

The main objective of the present work is to perform stress analysis on composite laminates under unaxial/biaxial loading to serve as a preliminary data for test verification. A detailed calculation based on the Classical Lamination Theory was performed for a laminate. The material used was carbon/epoxy applying a pure uniaxial load followed by a biaxial load. It was observed that the failure ...

Modeling of Ferrofluid Passive Cooling System

M. Yang[1,2], R. O'Handley[2], and Z. Fang[2,3]
[1]Massachusetts Institute of Technology, Cambridge, MA, USA
[2]Ferro Solutions, Woburn, MA, USA
[3]Pennsylvania State University, University Park, PA, USA

A ferrofluid contains nanoscale ferromagnetic particles suspended in a carrier liquid. It is used in some high-power acoustic speakers to cool the drive coil. The ferromagnetic particles far from the heat source are attracted by the drive coil’s magnetic field. As the fluid approaches the heat source, its temperature rises, causing the nanoparticles to become paramagnetic. Cooler magnetic fluid ...

Characterization of an AlGaN/GaN Electrostatically Actuated Cantilever Using the Finite Element Method

N. DeRoller, M. Qazi, J. Liu, and G. Koley
University of South Carolina, Columbia, SC, USA

AlGaN/GaN heterostructures are unique because the 2DEG at the interface is created by the difference in polarization properties of the AlGaN and the GaN layers; not due to intentional doping. In this work, a 3D model of an electrostatically actuated micro cantilever has been developed using COMSOL for characterization using the finite element method (FEM). The microcantilever has AlGaN/GaN HFET ...

Uncertainty Analysis, Verification and Validation of a Stress Concentration in a Cantilever Beam

S. Kargar, and D. Bardot
University of Alabama, Huntsville, AL, USA

In this paper we compare the results from a bending cantilever beam experiment with the theoretical values and COMSOL finite element simulation results. In the experiment a simple cantilever beam with a hole is loaded at the end. Measurements are recorded by four strain gauges mounted on the beam, three near the hole and one at a location where the nominal stress is equivalent to that of a ...

Finite Element Analysis of Pipes Considering the Effects of Stress Concentration Due to Dents

S.C. de Oliveira[1], E.P. de Deus[2], and A.M. Mont'Alverne[2]
[1] Funcap/CNPq, CE, Brazil
[2] Universidade Federal do Ceara, Fortaleza, CE, Brazil

This paper presents a numerical analysis of indented pipes based on the Finite Element (FE) within the framework of COMSOL Multiphysics. Numerical models using two-dimensional solid plane strain elements are evaluated. Geometric nonlinear analysis, nonlinear isotropic hardening material and contact were also incorporated into the models. The numerical models are calibrated by using an ...

Simulations of Meniscus Motion and Evaporation for Convective Deposition Manufacturing

J. Xiao, and D. Attinger
Columbia University, New York, NY, USA

Convective deposition is a material processing technique where an evaporating meniscus of a colloidal suspension is dragged along a solid substrate to deposit layers of micro or nanoparticles. The process is a typical multiphysics process where fluid dynamics, mass and heat transfer come into play in a small deforming domain. In this work, we describe an Arbitrary Lagrangian-Euler model ...

The Transient Modeling of Bubble Pinch-Off Using an ALE Moving Mesh

C.J. Forster, and M.K. Smith
Georgia Institute of Technology, Atlanta, GA, USA

The use of an acoustic field to control the boiling process has the potential to increase the overall rate of heat transfer and delay the critical transition to film boiling. This system is being investigated through the development of a model of a single boiling bubble near a flat, heated, horizontal surface in the presence of an acoustic field. The dynamics of the bubble interface is ...

Hydro-Mechanical Modelling of a Shaft Seal in a Deep Geological Repository

D. Priyanto
Atomic Energy of Canada Limited, Pinawa, MB, Canada

The hydro-mechanical (HM) numerical simulation of a shaft seal installed at a fracture zone in a hypothetical host rock using COMSOL is presented. Two different stages are considered in the numerical modelling. Stage 1 simulates the groundwater flow into an open shaft. Stage 2 simulates the groundwater flow after installation of shaft sealing-components. The shaft sealing components include: ...