N. Elabbasi, J. Bergstrom, and S. Brown
Veryst Engineering, LLC.
Peristaltic pumping is an inherently nonlinear multiphysics problem where the deformation of the tube and the pumped fluid are strongly coupled. We used COMSOL Multiphysics to investigate the performance of a 180 degree rotary peristaltic pump with two metallic rollers, and an elastomeric tube pumping a viscous Newtonian fluid. The model captures the peristaltic flow, the flow fluctuations ...
S. Loire, and P. Kauffmann
University of California
Santa Barbara, CA
Recently, electrokinetic flows have raised the interest of the scientific community. Driving flow with an electric field leads to promising applications for mixing, concentration, pumping application in lab on chips. However, current models are still inaccurate and don\'t fit the measures. The simple decoupled model developed by Ramos et al does not predict velocities for all parameters. ...
A. Roday, and P. Nicosia
Garlock Sealing Technologies
Sintering is an important step in the manufacturing of polytetrafluoroethylene (PTFE) billets. The challenge in heating large billets stems from the inherent low thermal conductivity of PTFE. Existing literature suggests determining maximum heating rate experimentally using recommended guidelines. This paper uses COMSOL to aid in optimizing the temperature profile required for a particular ...
T. Kaya, B. Shiari, K. Petsch, and D. Yates
Central Michigan University, School of Engineering and Technology, Mount Pleasant, MI
University of Michigan, Dept. of Electrical Engineering and Computer Science, Ann Arbor, MI
In this work, a MEMS low-g accelerometer with three sensitive directions is designed for health monitoring applications. The accelerometer may have different sensitivity in different axes. The proof-mass of the device is suspended by four serpentine springs, and the comb drive structure is used to form the differential capacitor to measure the displacement of the proof-mass. The structure has an ...
D. Groulx, and R. Murray
COMSOL Multiphysics can be used to model a latent heat energy storage system. A 2D numerical study was performed to simulate melting of a PCM including both conduction and convective heat transfer. The heat transfer in fluids and laminar flow physics interfaces were used. To model natural convection, proper volume force was applied to the PCM. The viscosity was input as a piecewise, continuous ...
D. Chandler, J. Freels, R. Primm III, and G. Maldonado
Department of Nuclear Engineering, University of Tennessee, Knoxville, TN
Research Reactors Division, Oak Ridge National Laboratory, Oak Ridge, TN
Primm Consulting, LLC., Knoxville, TN
The computational ability to accurately predict the dynamic behavior of a nuclear reactor core in response to reactivity-induced perturbations is an important subject in reactor physics. Space-time and point kinetics methodologies were developed for the purpose of studying the transient-induced behavior of the High Flux Isotope Reactor’s (HFIR) compact core. The space-time simulations employed ...
Micro and Nanotechnology Program
Middle East Technical University
In this study, a new thermoelectric harvester with fluid flow for increased performance is introduced. The thermoelectric generator is 3D vertical configuration with p- and n-doped Silicon thermolegs. There is water flow between channels integrated through the thermoelectric columns, providing forced convection on the heat flow path. Our thermoelectric generator design can be used for energy ...
J. Crompton, S. Yushanov, L. Gritter, and K. Koppenhoefer
AltaSim Technologies, LLC.
Thermoelectric phenomena provide the direct conversion of heat into electricity or electricity into heat, the phenomena is described by three related mechanisms: the Seebeck, Peltier and Thomson effects. Thermoelectric devices have found many applications ranging from temperature measurement, solid state heating or cooling and direct energy conversion from waste heat. In this paper, analysis ...
Designers of electro-optic modulators and related devices often use separate tools to study the optical and electrical portions of the device. The flexibility of COMSOL Multiphysics makes it possible to construct unified models of EO phenomena including realistic waveguide profiles and anisotropic material properties. We demonstrate the use of the RF Module to compute both RF and optical ...
N. Bhalla, S. Li, and D. Chung
Chung Yuan Christian University, Taiwan, (R.O.C)
National Tsing Hua University, Taiwan, (R.O.C)
Different configurations of MEMS based accelerometer has been made and analysed using COMSOL Multiphysics. The designs presented in this paper consist of a square shaped proof mass with flexures supporting it. Different position and varied number of supporting flexures attached to the proof mass makes each configuration distinct. The piezoresistors are placed near the proof mass and frame ends ...