M. Mor, C. Seneci, V. Zacché, C. Remino, G. Petrogalli, D. Fausti
Polibrixia, Brescia, Italy
This paper presents the study and design of a new generation oven for PET blow-molding machines. The design faced several technical challenges such as: the temperature distribution in the critical areas, the sharp curvature radius, the high PET thermal inertia and the presence of boundary elements, which affected the overall performances. The work included an analysis of the preform material ...
F. Lima, U. Mescheder, H. Reinecke
Hochschule Furtwangen University, Furtwangen, Baden-Wuerttemberg, Germany
Institut für Mikrosystemtechnik, Freiburg im Breisgau, Baden-Wuerttemberg, Germany
Electrodeposition has a major advantage over other methods of thin film deposition. It allows deposition at atmospheric pressure and room temperature, requiring inexpensive equipment. However, there are several parameters which can influence an electroplated metal layer quality. The current density distribution is taken into consideration. The Hull cell is an electrodeposition tank with a ...
Y.F. Wang, Y.S. Wang, L. Wang
Institute of Engineering Mechanics, Beijing Jiaotong University, Beijing, China
Department of Mechanical Engineering, Østfold University College, Halden, Norway
We show in this paper that by careful design of the geometry of the resonators, complete bandgap with relatively low center frequency can be obtained for 2D and 3D Phononic Crystals with resonators. The generation of the bandgap is due to the local resonance of the unit cell. Spring-mass and spring-pendulum models are developed to predict the boundaries of the complete bandgap. The predicted ...
Current Density Distribution and Material Removal Behavior on the Graphite/Iron-matrix Interface in Cast Iron Under Pulse Electrochemical Machining Conditions
O. Weber, R. Kollmannsperger, D. Bähre
Center for Mechatronics and Automatization, Saarbrücken, Germany
Institute of Production Engineering, Saarland University, Saarbrücken, Germany
The Pulse Electrochemical Machining is especially suitable for the precise production of complex geometric contours with high precision and high surface quality demands in workpieces in series manufacturing. During this process, the negative structure of an electrode is copied to the workpiece without sub-surface damages. An adequate knowledge of the current density distribution and thus of the ...
E. Licon, S. Casas, A. Alcaraz, J.L. Cortina, C. Valderrama
Universitat Politécnica de Catalunya, Barcelona, Spain
Ammonia separation from water by membrane contactor was simulated on transient state and compared with experimental data. Aqueous low concentrated solution of ammonium with high pH has been pumped inside the hydrophobic hollow fibers, acid solution in the outside part. The system is in closed loop configuration. In order to simulate the separation process, equations were developed considering ...
U. N. Mughal, M. S. Virk
Narvik University College, Narvik, Norway
Atmospheric ice is a very complex material with varying electrical properties due to different polymorphs of ice itself. Also, if the medium to be considered is snow, then density becomes an additional parameter because it is a mixture of three dielectrics water, ice and air. The permittivity and loss tangent of naturally occurring ice and snow shows lot of variation at different conditions ...
Numerical Modeling of Powder Flow During Coaxial Laser Direct Metal Deposition: Comparison Between Ti-6Al-4V Alloy and 316L Stainless Steel
S. Morville, M. Carin, D. Carron, P. Le Masson, M. Gharbi, P. Peyre, R. Fabbro
Université de Bretagne-Sud/UEB-LIMATB, Lorient, France
PIMM, Arts et Métiers ParisTech, Paris, France
This paper presents a 3D numerical model to predict the whole process of coaxial powder flow, including the particle stream flow in and below the nozzle and also the laser-particle interaction process. The Particle Tracing Module of COMSOL Multiphysics is used to solve the coupled momentum transfer equations between the particle and gas phase while incorporating particle temperature evolution. A ...
H. Bruus, P.B. Muller, R. Barnkob, M.J.H. Jensen
Technical University of Denmark, Kongens Lyngby, Denmark
COMSOL, Kongens Lyngby, Denmark
We have simulated the ultrasound-induced acoustophoretic motion of microparticles suspended in an aqueous solution. The full first-order thermoviscous acoustics equations have been implented on a rectangular microfluidic 2D domain excited with an ultrasound field tuned to resonance near 2 MHz. The micrometer-thin but crucial viscous boundary layers at the rigid walls have been fully resolved. ...
University of Turku, Turku, FInland
An experimental LED light composed of a multi-chip LED-module, a LED driver and an efficient heat sink, was investigated using COMSOL Multiphysics software and the Heat Transfer Module. In an LED light heat is mainly generated in the LEDs but some amount of heat is generated also in the LED driver. The main target of the simulations was to resolve the junction temperatures of LEDs, the most ...
V. Pavelko, I. Pavelko, M. Smolyaninovs, H. Pffeifer, M. Wevers
Riga Technical University, Riga, Latvia
Catholic University Leuven, Leuven, Belgium
A problem of damage prediction in aircraft structure and its non-destructive evaluation is very important for aircraft structural health assessment. The analysis of the features of direct impact of thin-walled laminate component of aircraft was performed by COMSOL Multiphysics software. Mainly the GFRC and CFRC laminates were selected in form either thin separate plate or sandwich structure. The ...