M. Giansetti, A. Pezzin, S. Sicardi, G. Rovero
Politecnico di Torino, Torino, Italy
Within wool textile industries, a very important role is played by the so-called finishing processes, in which the textile substrate undergoes steam treatments to achieve the desired level of stabilisation and appearance. Process parameters, namely temperature and moisture content, are known only at the beginning of the process but not in the textile material being treated, where the actual ...
A. Czirják, Z. Kőkuti, G. Tóth-Molnár, P. Ailer, L. Palkovics, G. Szabó
University of Szeged, Szeged, Hungary
Kecskemét College, Kecskemét, Hungary
In certain cases, the accuracy of measurements with a rotational rheometer can be influenced by inefficient thermal management, by the heat generated in the sample, or by rod-climbing due to the Weissenberg effect. We investigate the effect of these phenomena with simulations in COMSOL Multiphysics®. Our model is based on the axial symmetric (2D) formulation of the two-phase flow with the ...
G. V. B. Lukasievicz, N. G. C. Astrath, L. C. Malacarne, M. L. Baesso, S. E. Bialkowski
Universidade Tecnológica Federal do Paraná, Toledo, PR, Brazil
Universidade Estadual de Maringá, Maringá, PR, Brazil
Utah State University, Logan, Utah, USA
The radiation force effects on the surface displacement can be calculated by solving the Navier-Stokes equation with appropriated boundary conditions. The surface deformation can be described by the radiation pressure as well as those forces due to gravity and surface tension. We used the photomechanical mirror (PM) method to measure the time-evolution of the nanometer deformation generated on ...
T. J. Kazdal , M. J. Hampe ,
 Technische Universität Darmstadt, Darmstadt, Germany
A micro steam methane reformer is a complex product consisting of multiple units. For the virtual functional product development it is necessary to validate these sub models separately. Therefore a reactor was designed to analyse kinetics of chemical reactions. The reactor design is based on a simulation geometry and the boundary conditions of the simulation were recreated in the experimental ...
A. A. Roy, V. Bojarevics, and K. Pericleous
University of Greenwich
The aim of this article is to demonstrate the capability of the software for predicting free-surface motion and internal fluid flow in an electromagnetically levitated sample of liquid metal. Multiphysics solutions which demonstrate the usefulness of Comsol as a powerful MHD simulation tool have been generated to two industrial problems using the ALE moving-mesh module in combination with the ...
Research Center for Power Engineering Problems of the Russian Academy of Sciences, Kazan, Russia
The influences of curvature effects and swirl intensities for Non-Newtonian viscous fluid flow in a curved tube have been numerically investigated by using COMSOL Multiphysics®. The twisted tape, which are located directly in front of the curved part, are used as swirl flow generators. The tape is twisted until it reaches an angle of 90 degrees and turns right. Swirling flow, getting into the ...
A. Nardi, E. Abarca, F. Grandia, J. Molinero
Amphos 21, Barcelona, Spain
The capture and storage of CO2 in deep geological formations is one of the proposed solutions to reduce CO2 emissions to the atmosphere. CO2 is injected as a supercritical fluid deep below a confining geological formation that prevents its return to the atmosphere. In general, four trapping mechanisms are expected, which are of increasing importance through time: (1) structural, (2) residual ...
KTH Royal Institute of Technology, Stockholm, Sweden
In this report I study the airflow through ventilation ducts. By numerical simulation, the so-called k-factor has been estimated. The k-factor is the quotient of the airflow volume and the square root of the pressure drop over the duct. A two dimensional axial symmetric model has been used to simulate an iris damper connected to a straight pipe. A three dimensional model has been used to ...
CFD Analysis of Loss Of Vacuum Accident for Safety Application in Experimental Fusion Reactor Facility
C. Bellecci, P. Gaudio, I. Lupelli, A. Malizia, M.T. Porfiri, R. Quaranta, and M. Richetta
EURATOM, Faculty of Engineering, University of Rome “Tor Vergata”, Roma, Italy
ENEA Nuclear Fusion Tecnologies, Frascati, Roma, Italy
In an experimental nuclear fusion facility dust is generated both during normal machine operations and by macroscopic erosion of the plasma facing materials due to intense thermal loads. This dust can be mobilized by air ingress in case of LOVA (Loss of Vacuum Accident) threaten safety of workers and public. A small facility, Small Tank for Aerosol Removal and Dust (STARDUST), was set up in ...
J. Hrdlicka, P. Cervenka, and D. Snita
Institute of Chemical Technology Prague, Prague, Czech Republic
This contribution is devoted to the mathematical modeling of the AC electroosmotic micropumps in COMSOL Multiphysics and Matlab. The mathematical model involves the microchannel surroundings and several AC-voltage driving modes. The weak form has been used for handling singularities and other problems. The system dynamic behavior and conditions at the phase interfaces will be discussed.