B. Niu, W. Yan, A.A. Shapiro, and E.H. Stenby
Department of Chemical and Biochemical Engineering, Technical University of Denmark, Kgs. Lyngby, Denmark
As an effective method to cope with green-house gas emission, and to enhance oil recovery, injection of carbon dioxide into oil reservoirs has obtained increasing attentions. The flooding process involves complex phase behavior among oil, brine and CO2, and geochemical reaction between CO2 and rock. COMSOL Multiphysics® was first applied to simulating two flooding processes with known ...
P. Schmitz, A. Cockx, S. Geoffroy, and J. Gunther
Biochemical Engineering Dpt., Université de Toulouse, Toulouse, France
Chemical Engineering Dpt., Université de Toulouse, Toulouse, France
Mechanical Engineering Dpt., Université de Toulouse, Toulouse, France
An undergraduate course is developed to initiate future engineers to multiphysics numerical simulation by approaching concrete cases in various fields such as: heat transfers, fluid flow, mechanics, chemistry and electrostatics. The so called “Virtual Experiments” course consists of four projects given successively to students. Each project lasts about ten hours. The major notions related to ...
G. Jehle, D. Kern, and W. Seemann
Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
This paper proposes the design of a 3-Degree of Freedom(DoF) motor based on surface acoustic waves in elastic solids. The rotor is propelled by wave fields, for linear and rotational motion respectively, in the stator, that can be steered by the driving signal of the piezoelectric actuators, which are placed on an elastic plate. The next considerations concern the feasibility of the proposed ...
A.T. Vermeltfoort, and J. van Schijndel
Eindhoven University of Technology, the Netherlands
The tensile strength of masonry is relatively low compared to its compressive strength and is affected by the direction of the joints and their filling. In masonry with modern thin layer mortar (joint thickness 3 to 5 mm) sometimes the head joints are left open. A total of 13 model-walls was built and for each model four general purpose mortar combinations and three thin layer mortar ...
S. Druart, D. Flandre, and L.A. Francis
Université catholique de Louvain - ICTEAM, Louvain-la-Neuve, Belgium
In this paper, a methodology to simulate the electric behavior of spiral inductances is presented and discussed. All the methodology is built with the COMSOL software used with the Matlab scripting interface and then allows performing fully parameterized simulations. The program architecture is explained and is used to simulate two applications. The first calculates the voltage induced by an ...
Verification and Time Performance Analysis of COMSOL v3.5a for Solving the Electromagnetic Problem in a Superconductor Slab
J. Lloberas, J. López, E. Bartolomé, and X. Granados
Universitat Politècnica de Catalunya, Barcelona, Spain
Escola Universitària Salesiana de Sarrià, Barcelona, Spain
Institut de Ciència de Materials de Barcelona, Barcelona, Spain
Numerical analysis based on finite element method (FEM) represents a powerful approach to solve electromagnetic problems. For instance, FEM methods have been broadly used to calculate the critical state current distribution in high temperature superconductors of various geometries. In the near future, we intend to develop a tool in COMSOL v3.5a for the analysis of power applications, such as ...
Chinese Academy of Sciences, Dalian Institute of Chemical Physics, Beijing, China
We studied the transient characteristics of PEMFC and water transport during PEMFC start-up, concerning the following aspects: Effect of air stoichiometry change on transient behavior of PEMFC, Transient behavior of water transport during PEMFC start-up, and high temperature PEMFC modeling.
Evaluation of Tensile Modulus of Carbon Nanotube Bundle Based Composite with Interface Using Finite Element Method
M. S. Islam, F. O. Riktan, S. C. Chowdhury, M. M. R. Chowdhury, and S. Ahmed
Bangladesh University of Engineering & Technology (BUET)
Carbon Nanotubes (CNTs) have remarkable mechanical, thermal and electrical properties. The properties of CNTs depend on atomic arrangement (how the sheets of graphite are rolled), the diameter and length of the tubes and morphology of nanostructure. In this paper effective elastic properties of CNT based polymer composites are evaluated using a square Representative Volume Element (RVE) in ...
University of Miami
Electric fields are present in biological systems at multiple spatial and temporal scales. Electroosmotic flow results from the action of electric field on the electrical double layer, formed at the fluid/solid or fluid/membrane interface and characterized by its zeta-potential. For the physiological value of zeta-potential (50 mV) and a single charged protein of average size, electroosmotic ...
A. Helfrich-Schkarbanenko, M. Mitschele, S. Ritterbusch, and V. Heuveline
Engineering Mathematics and Computing Lab (EMCL), Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
Institute for Analysis, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
We consider a 3D boundary value problem arising in electrostatics. The potential is stimulated by current sources placed on a cross-section S of the domain. In many applications it is sufficient to know the potential in S. So, one is interested in an appropriate 2D model taking into account that the solution depends on the dimension of the domain. The idea is to find a corresponding 2D ...